故事是这样的：What's up? (sorry but I can only type in English on my computer)
万分感谢您的回复。我现在就是这么做的。但从我的路由器上看，wan口依然是172的地址。看了您的回复，我又试了一下，居然可以从外面访问路由器了。（记得前几天试还不行，不知道原因了）。我之前一直纠结路由器wan口是不是公网地址了。Actiontec v1000h is also called gateway. In a more general term, it is modem as on the copper xDSL high speed lines.
And the ONT is more like a signal converter that converts the optic fibre signal to the electric signal that goes to Actiontec.
In terms of your first question, it is not doable: connecting your router to ONT directly will not give you the public IP address you want.
However, if you connect your own router to the LAN port on Actiontec, and then configure Actiontec properly, your router should be able to use the modem (Actiontec) WAN IP address as its own. The modem (Actiontec) WAN IP address is a public IP that can be found from the Actiontec GUI, for example, 142....
Please follow the steps below to configure the Actiontec gateway from any of your computers that is connected directly to the Actiontec network either through wi-fi or ethernet:
1. Make sure your router is connected to an Actionac gateway LAN port;
2. From your computer, go to 172.16.1.254 which will give you Actiontec GUI;
3. From the top right hand, there is a Password field that is supposed to be the default 10 character system password located at the bottom of the Actiontec gateway box. If you have never changed this login password, that default system password should let you login to Actiontec interface.
4. After you login, you will see a list of all the devices that are currently connected the Actiontec. One of those devices should be your router and router should be with a private IP like 172...
5. Next, click on Firewall.
6. From the left side, click on DMZ Hosting.
7. Go through the 3 steps under DMZ Hosting: Enable - Select a device (your router) - Apply
Your router should now be accessible by the Actiontec WAN IP Address (public IP) located at the top left side of the home page of the Actiontec GUI.
(This bypasses the firewall on Actiontec and exposes your router directly to the external network. Actiontec WAN IP address may change once Actiontec gets rebooted -- static IP won't change. So you need to know what you are doing.)
Hope the above will get you started toward the right direction.
另外，v1000h的DMZ设置是不是只基于设备的IP地址呀，如果那样，IP换了，每次都要重做Actiontec v1000h is also called gateway. In a more general term, it is modem as on the copper xDSL high speed lines.
And the ONT is more like a signal converter that converts the optic fibre signal to the electric signal that goes to Actiontec.
In terms of your first question, it is not doable: connecting your router to ONT directly will not give you the public IP address you want.
However, if you connect your own router to the LAN port on Actiontec, and then configure Actiontec properly, your router should be able to use the modem (Actiontec) WAN IP address as its own. The modem (Actiontec) WAN IP address is a public IP that can be found from the Actiontec GUI, for example, 142....
Please follow the steps below to configure the Actiontec gateway from any of your computers that is connected directly to the Actiontec network either through wi-fi or ethernet:
1. Make sure your router is connected to an Actionac gateway LAN port;
2. From your computer, go to 172.16.1.254 which will give you Actiontec GUI;
3. From the top right hand, there is a Password field that is supposed to be the default 10 character system password located at the bottom of the Actiontec gateway box. If you have never changed this login password, that default system password should let you login to Actiontec interface.
4. After you login, you will see a list of all the devices that are currently connected the Actiontec. One of those devices should be your router and router should be with a private IP like 172...
5. Next, click on Firewall.
6. From the left side, click on DMZ Hosting.
7. Go through the 3 steps under DMZ Hosting: Enable - Select a device (your router) - Apply
Your router should now be accessible by the Actiontec WAN IP Address (public IP) located at the top left side of the home page of the Actiontec GUI.
(This bypasses the firewall on Actiontec and exposes your router directly to the external network. Actiontec WAN IP address may change once Actiontec gets rebooted -- static IP won't change. So you need to know what you are doing.)
Hope the above will get you started toward the right direction.
Actiontec v1000h is also called gateway. In a more general term, it is modem as on the copper xDSL high speed lines.
And the ONT is more like a signal converter that converts the optic fibre signal to the electric signal that goes to Actiontec.
In terms of your first question, it is not doable: connecting your router to ONT directly will not give you the public IP address you want.
However, if you connect your own router to the LAN port on Actiontec, and then configure Actiontec properly, your router should be able to use the modem (Actiontec) WAN IP address as its own. The modem (Actiontec) WAN IP address is a public IP that can be found from the Actiontec GUI, for example, 142....
Please follow the steps below to configure the Actiontec gateway from any of your computers that is connected directly to the Actiontec network either through wi-fi or ethernet:
1. Make sure your router is connected to an Actionac gateway LAN port;
2. From your computer, go to 172.16.1.254 which will give you Actiontec GUI;
3. From the top right hand, there is a Password field that is supposed to be the default 10 character system password located at the bottom of the Actiontec gateway box. If you have never changed this login password, that default system password should let you login to Actiontec interface.
4. After you login, you will see a list of all the devices that are currently connected the Actiontec. One of those devices should be your router and router should be with a private IP like 172...
5. Next, click on Firewall.
6. From the left side, click on DMZ Hosting.
7. Go through the 3 steps under DMZ Hosting: Enable - Select a device (your router) - Apply
Your router should now be accessible by the Actiontec WAN IP Address (public IP) located at the top left side of the home page of the Actiontec GUI.
(This bypasses the firewall on Actiontec and exposes your router directly to the external network. Actiontec WAN IP address may change once Actiontec gets rebooted -- static IP won't change. So you need to know what you are doing.)
Hope the above will get you started toward the right direction.
是的，我现在也这么做了。基本的要求全实现了。下一步是照搬这个配置到国内家里，反向翻墙，便于看视频啥的。DDNS的配置在v1000h上做，vpn 在路由器上做就可以了。我是这样搞的，效果还可以。
DDNS的配置在v1000h上做，vpn 在路由器上做就可以了。我是这样搞的，效果还可以。